MILKIT VALVES MAKE USING TUBELESS SYSTEMS CLEAN AND EASY
easy
Refill sealant through the valve – tire stays inflated without the valve core
quick
Check sealant levels while the tire stays inflated
clean
Tires are mounted dry and the valve design prevents clogging
NO MESS & NO AIR LOSS
EVEN WITHOUT THE VALVE CORE
milKit patented tubeless valve system is quick and easy to use:
- Smart rubber flaps ensure no air is lost when the valve core is removed and sealant does not block the valves
- Use the syringe to easily check if enough sealant remains in your tire
- The syringe accurately measures the amount of sealant needed
- No more mess as tires can be installed dry and sealant added afterwards through the valve
- Kit contains measuring & refilling syringe, valves, and valve core removal tool
TAKE A LOOK AT HOW THE MILKIT
VALVE SYSTEM WORKS:
HOW TO USE MILKIT VALVES & SYRINGE
This patented system enables clean and easy tubeless tire setup.
- Install valve and screw out the milKit valve core
- Pre-inflate your tire up to 22 psi (we recommend the milKit Booster) – the rubber flaps ensure no air is lost even with the valve core removed
- (For maintenance rather than installation of new tire) Extract old sealant from tire with the milKit syringe to measure remaining amount and check quality
- Measure out the correct amount of sealant and inject using the syringe
- Screw the valve core back in, inflate tire to full pressure until the tire fully jumps onto the rim and you’re ready to ride!
The solution to combat sealant drying out or escaping! With other tubeless tire valve systems you need to remove the tire to check if enough sealant remains, with milKit you can simply remove the valve core and insert the syringe to check. No mess and faster results!
The syringe holds 60ml or 2 oz of fluid and comes with a flexible connector and a large needle to push through the valve and rubber flaps. There’s also a sealant regulator that screws into the syringe for easy refilling. The needle has an angled end for effective removal of all sealant in the tire.
Patented milKit presta bike valves are made in Germany from anodized high quality aluminum alloy and high performance rubber for the smart flaps.
The standard milKit valves have a usable length of 35 mm (1 3/8 inch), and they work for most road and mountain bike rims except some special high-profile rims. For high-profile rims, there are 45mm, 55mm and 75mm versions of the milKit valves available.
milKit valves can be used with most sealants, but we recommend milKit sealant. This has been specially designed for best results with these valves.
Replacement valves & valve cores are also available.
THE MILKIT VALVE SYSTEM IS AVAILABLE IN THE FOLLOWING
PRODUCT VERSIONS:
MILKIT COMPACT 35
- 2x 35mm milKit valves
- 1x measuring and refilling syringe
- 1x valve core tool
- 2x milKit rim stickers
MILKIT COMPACT 45
- 2x 45mm milKit valves
- 1x measuring and refilling syringe
- 1x valve core tool
- 2x milKit rim stickers
MILKIT COMPACT 55
- 2x 55mm milKit valves
- 1x measuring and refilling syringe
- 1x valve core tool
- 2x milKit rim stickers
MILKIT COMPACT 75
- 2x 75mm milKit valves
- 1x measuring and refilling syringe
- 1x valve core tool
- 2x milKit rim stickers
MILKIT VALVE PACK 35
- 2x 35mm milKit valves
- 1x valve core tool
- 2x milKit rim stickers
MILKIT VALVE PACK 45
- 2x 45mm milKit valves
- 1x valve core tool
- 2x milKit rim stickers
MILKIT VALVE PACK 55
- 2x 55mm milKit valves
- 1x valve core tool
- 2x milKit rim stickers
MILKIT VALVE PACK 75
- 2x 75mm milKit valves
- 1x valve core tool
- 2x milKit rim stickers
